BJT vs MOSFET comes down to how each transistor is controlled and where it loses energy. A BJT (bipolar junction transistor) is current-driven and cheap with high gain, while a MOSFET (metal-oxide-semiconductor field-effect transistor) is voltage-driven, switches faster, and wastes less power in most switching jobs. As a rule of thumb, choose a MOSFET for efficient power switching and high frequency, and choose a BJT for low-cost signal switching, simple amplification, or very low-current analog stages. This guide explains how each device works, the key differences, when to use which, and how to source the right part in Europe.
Both are three-terminal semiconductor switches, so they look interchangeable on a schematic, but their internal physics makes them behave very differently under load. Picking the wrong one costs efficiency, heat, and board space, so the decision is worth getting right early in a design.
What Is a BJT?
A BJT is a current-controlled transistor with three terminals: base, collector, and emitter. A small base current controls a much larger collector current, set by the current gain (hFE or beta). Because conduction uses both electrons and holes (bipolar), a BJT has a roughly fixed collector-emitter saturation voltage of a few tenths of a volt when fully on. BJTs are inexpensive, offer high gain, and remain popular in analog amplifiers, low-power signal switching, and references.
What Is a MOSFET?
A MOSFET is a voltage-controlled transistor with a gate, drain, and source. A voltage on the insulated gate creates a channel that lets current flow from drain to source, so the gate draws almost no steady current. Its on-state behaves like a low resistance (RDS(on)), so conduction loss rises with the square of current. MOSFETs switch quickly with low drive power, which makes them the default choice for switch-mode power supplies, DC-DC converters, and motor drives.
BJT vs MOSFET: The Key Differences
A BJT needs a continuous base current and drops a fixed VCE(sat) of roughly 0.1 to 0.3 V when on. A MOSFET needs only gate voltage and behaves like a resistor, RDS(on), when on. Every other difference in the table follows from those two facts:
| Attribute | BJT | MOSFET |
|---|---|---|
| Control | Current-driven (base current) | Voltage-driven (gate voltage) |
| Drive power | Continuous base current needed | Almost zero steady gate current |
| On-state | Fixed saturation voltage (VCE(sat)) | Resistive (RDS(on)) |
| Switching speed | Slower (carrier storage time) | Faster (no storage time) |
| Input impedance | Low | Very high |
| Thermal behavior | Prone to thermal runaway | Stable, easy to parallel |
| Typical use | Amplifiers, low-power signal switching | SMPS, DC-DC, motor and power switching |
When to Use a BJT
Use a BJT for low-current signal switching, linear gain and low-cost designs where a few tenths of a volt of saturation loss does not matter. Typical cases:
- Small-signal switching of LEDs, relays, and logic-level loads where current is low.
- Linear amplification in audio, sensor front-ends, and discrete analog stages.
- Low-cost, low-voltage designs where a few tenths of a volt of saturation loss is acceptable.
A stocked example: the onsemi SMUN5312DW1T1G puts a pre-biased NPN and PNP pair (bias resistor transistors) into one SOT-363 package for digital switching, so no external base resistors are needed. GlobX holds 12,000 pieces at date code 25+, status active as of October 2026. If you need to match the 6-pin footprint with another brand, our SMD package size chart lists the SOT-363 aliases (SC-88, SC-70-6).
When to Use a MOSFET
Use a MOSFET when the job is power switching above about an amp, switching above tens of kHz, or switching driven straight from a logic pin. Typical cases:
- Power switching in SMPS, DC-DC converters, and battery management where low RDS(on) cuts heat.
- High-frequency loads (Class-D audio, synchronous rectification) that need fast, low-loss switching.
- Motor control and load switches where the gate can be driven directly from a controller or driver.
At the small-signal end, the Nexperia BSS138BK is the classic logic-level N-channel MOSFET for level shifting and load switching, in SOT-23 (date code 2026, status active at GlobX as of October 2026). It also shows why small MOSFETs carry supply risk. BSS138 and 2N7002 parts are designed into millions of boards, and Nexperia supply has been disrupted in 2025-2026. Our Nexperia alternatives guide lists cross-brand options.
How to Choose Between a BJT and a MOSFET
Pick a MOSFET if the load is above about 1 A, the switching frequency is above tens of kHz, or a microcontroller pin drives the switch directly. Otherwise a BJT is usually the cheaper and simpler choice. Check four questions in order:
- Is it switching or amplifying? For efficient on/off power switching, lean MOSFET. For linear gain, a BJT is often simpler.
- How much current? Above roughly an amp, a MOSFET's resistive loss usually beats a BJT's fixed saturation drop and base-current overhead.
- What switching frequency? Above tens of kHz, MOSFET speed and low drive power win; below that, a BJT can be fine.
- What is the drive available? A microcontroller pin can drive a logic-level MOSFET gate directly, while a BJT needs a base resistor and continuous current.
Where IGBT and SiC Fit
At high voltage and high current the comparison extends beyond these two devices. The IGBT combines a MOSFET-style gate with a bipolar output for high-power, lower-frequency stages, while silicon-carbide (SiC) MOSFETs deliver high voltage with fast switching. If your design sits at mains voltage or above, read our companion guide on MOSFET vs IGBT, and see a worked power-MOSFET example in the Infineon IPA60R360P7 CoolMOS post. For a wider map of part families, see our guide to the types of electronic components.
How GlobX Helps You Source BJTs and MOSFETs
GlobX is an independent distributor and supply-chain specialist that sources transistors and power semiconductors from a verified global network and the open market, with ISO 9001 processes, anti-counterfeit inspection, full traceability, and 24-hour quotes. Small-signal transistors are among the most counterfeited parts, so check traceability before you buy (see how to avoid counterfeit components). Before you accept a substitute, run it through our cross reference checklist. Whether you have settled on a device or need a second source during allocation, browse live MOSFETs in our catalog, search all component availability, or see how our electronic component sourcing works. Chasing an obsolete or allocated transistor? Send your part list to the GlobX team for a 24-hour quote.